Install Mirolin Showers Installation

How To Install A Neo-Angle Shower - Part 1 - Base Installation Installing A Neo-Angle Shower: Part 1 - The Base In This Article: The shower base is laid in place to mark the drain hole location. A hole is cut for the drain. Durock is bonded to the floor and the shower base is adhered to the cement board and screwed to the wall studs. Related Articles: • Index of Articles • • Part 2: • Part 3: Skill Level: 3 (Moderate) Time Taken: 2 Hours By, Editor Start: This 'neo-angle' corner shower has three main sections: the base, the shower surround that is glued to the walls, and the glass front. The base is the trickiest to install. This shower base had to be installed before the PVC drain plumbing could be completed. Consequently, the base may be subjected to some damage while the other tasks are completed (such as installing and finishing the drywall).
I set the shower base in place to determine if it would need any shims to make it level. Even after our extensive modifications, the floor still has a slight slope. This is the drain fitting supplied with the shower. It uses a black rubber gasket and a huge hex nut to seal against the shower base. The 2' PVC drain pipe seals against the corrugated rubber gasket on the inside of the fitting.
Whether you are replacing an existing shower or installing a new one, using a preformed, acrylic shower base is the fastest and easiest way to a new shower. Shower bases can now be purchased in many colors and styles. It can become the focal point for any bathroom renovation colour scheme. The style of shower base. Mirolin Industries Inc. I've lost hundreds on each install and Mirolin won. I also had two cracks show up in the tub and had to purchase Mirolin's tub.
Using a permanent marker, I carefully transferred the outline of the hole in the shower base onto the floor. I cut out the hole with a reciprocating saw. Even the side of a floor joist had to be trimmed slightly. The hole must be big enough to allow the hex nut to be removed or tightened using a pair of jumbo Channel-Lock pliers. The Cement-Board Underlayment: Then I cut the drain hole in the piece of Durock.
I used a jig saw with a carbide blade. I also could have used a reciprocating saw with a carbide blade. This jig saw blade is narrow and allows for easy cutting of curves. The holes actually lined up properly! Counselling Skills And Theory Margaret Hough Pdf.
The Durock was cut to (almost) exactly fit the shower base. I should have made the Durock exactly the same size as the base. I later had to trim off a thin strip. My original plan was to use ½' Durock as tile backer in the bathroom, but I later changed to ¼' Wonderboard, so the total floor thickness would not exceed the hardwood floor in the hallway.
I mixed up some thin-set mortar in a plastic tub. I applied some mortar to the floor, pushing the mud into the floor grooves with the smooth edge of the trowel. Then the notched side was used to create the proper bonding surface.
The Durock was laid in place and made level with some wood shims. Once the mortar has hardened, the shims won't be necessary. I tapped the high end with a hammer and a board. I drove in some 2-1/2' deck screws to hold down the Durock. The screws need to go into the floor joists. Earlier we had doubled-up the floor joists, so I marked each joist location and drove a few screws into each side.
I drove screws along twin layout lines, (lines that corresponded to the floor joists). In order to prevent the screw heads from sticking up, I had to pre-drill a small countersink for each screw. Since Durock is so hard, the screws will not bury their own heads, like they do in wood. I simply used a large carbide-tipped masonry drill bit to make the counter-sinks.
The cement board after installation. A Couple Of Days Later: The shower drain was installed onto the shower base, while the base was leaning against the wall. Just to be sure, I applied a bead of clear silicone under the flange of the drain before I installed it. I used a pair of 18' Channel-Lock pliers to tighten the nut.
This huge tool is very useful around the house, especially for plumbing projects. I applied a bead of Liquid Nails For Tub Surrounds to the Durock underlayment. I set the shower base in place and installed the 4 screws that held the base into the studs. (First I pre-drilled the holes) I applied as much weight as possible to hold the base down.
Old college textbooks were the best thing I could find. The next day, after the glue had dried, I removed the weights. This is an early stage in the remodeling project. It took over a month to do the rough plumbing and drywall work that enabled me to complete this installation.
Kernel For Pdf Repair Tool Crack Win here. Continue to the installation. Related Info: Read about a HammerZone.com visitor whose neo-angle shower had a. Used: • Cordless Drill/Driver• Masonry Drill Bits• Notched Flooring Trowel, ¼'x¼'• Reciprocating Saw• Jig Saw with Carbide Blade• 24' Level• 18' Channel-Lock Pliers Materials Used: • Shower Base• Durock, ½'• Deck Screws• Thinset Mortar• Liquid Nails For Tub Surrounds• Clear Silicone Before You Hurt Yourself, Read our. Copyright © 2000, 2005 HammerZone.com Written October 6, 2000 Revised January 3, 2005.